如何安装墙壁烛台吗

即使在光线充足的家中，一个或两个额外的HomeHome重音灯也可以立即增强风格和氛围。但是，如果您由于令人生畏的布线而避免了墙壁壁灯，那么您可以轻松休息。

有些墙壁尖叫着，以获得优雅的光线。无论是一个向上的固定装置，在墙壁和天花板上散发出温暖的光芒，还是一个瞄准的固定装置，旨在在舒适的阅读角上向下倾斜一些额外的照明，壁式壁灯都可以提供很多。这些固定装置可以侧面浴室镜子以提供任务照明，使原本黑暗的楼梯亮起，或在HomeHome在家办公for top-notch remote meetings.

但是，对于那些不知道如何安装墙壁壁炉的人来说，该项目似乎令人不知所措。不过，有个好消息：在正确的条件下，该项目比外观更容易接触。

您需要什么

工具：

材料：

• Fish tape
• Painter’s tape
• 14/2 non-metallic sheathed building wire
• 旧工作箱
• 旧工作天花板电盒
• Wire connectors
• 灯开关和盖板
• 带安装硬件的扫描

笔记：尽管有天花板的名称，但它将在墙上用作壁灯的接线盒。

安装墙壁壁con的最简单的地方

You can add a wall sconce almost anywhere, but for the least amount of work without many complications, you’ll want to install it a few feet above an existing electrical outlet. Since electrical outlets are installed between two studs running vertically, there are typically few obstructions to work around when running wires straight upward.

If there isn’t already an outlet to work above, it will be necessary to run wires to the wall sconce’s location. This may involve tearing down drywall or drilling through wooden bottom plates, neither of which are as easy as installing a sconce above an existing outlet.

How High to Install a Sconce

关于在哪里定位壁炉，没有艰难而快速的规则。因此，您可以将它们放在家具，床头板或绘画周围最佳的位置。但是，这些一般的高度建议将确保墙壁壁con与房间的其余部分保持正确的比例：

• 上方或周围的床头板：48 inches to 60 inches from the floor
• Around a bathroom vanity:60 inches to 70 inches from the floor
• 口音或任务照明：距地板60英寸至72英寸

如何安装墙壁烛台吗

1. Start by choosing the wall sconce’s location (above an outlet) and mark the spot with a piece of painter’s tape. Then, use a stud finder to ensure that the studs land within the same stud bay as the outlet. Use painter’s tape to mark the position of the studs.

笔记：Most existing electrical boxes are nailed directly to a stud, so ensure that the proposed sconce location and outlet are on the same side of the stud. If the outlet is to the right of the stud, the light must also then be to the right of the same stud.

2. Shut off the power at the breaker. Use a non-contact voltage tester to ensure that the outlet itself is no longer energized. Use the screwdriver to remove the cover plate and, again, check that the wiring within the electrical box isn’t energized by probing with the non-contact voltage tester. Once confirmed, remove the screws holding the outlet into the electrical box and pull it out from the box.

3. Choose a location for the light switch between the sconce’s proposed location and the outlet. Place the old work electrical box face-down against the wall’s surface at this location, level it, and trace around the box with a pencil. Carefully cut the box’s shape out of the drywall using the drywall saw.

4.将圆形的天花板电箱面向壁板上的干墙，以壁灯选择的位置。用铅笔在它周围痕迹，然后使用干墙锯将其切出。

5. With the wires inside the outlet box pushed to the side, slide the fish tape up from the inside of the box. Continue feeding fish tape up the wall until it’s visible from the hole for the sconce. Pull the fish tape out of the top hole.

6. Cut and remove about 6 inches of the plastic jacket on a length of 14/2 wire. Attach one of the wires to the fish tape by bending it through the hook and wrapping it around itself to create a removable knot. Fold the other two wires back flat against the remaining jacket. Slowly feed the wire down into the wall cavity while also retrieving the fish tape. Go slowly to prevent drywall damage. Pull the wire through the outlet’s electrical box.

7.从插座的电盒中拉出大约8至10英寸的电线。在孔中伸到孔内，然后将其从大约8到10英寸的孔中拉出，然后切入环中间的电线。从顶部孔的线轴上切下电线，使末端长约8至10英寸。

8. Working at the top hole first, push the wire through the round ceiling box. Then, fit the ceiling box into the hole, tightening the adjustable wings until it clamps into place.

9. Repeat the same process at the hole for the switch, feeding one length of wire through the top of the old work box and one length of wire through the bottom of the box before fitting it into the hole.

10.从壁灯套件中卸下安装硬件，然后将其连接到天花板电盒。每个套件略有不同，但大多数套件都有一个横跨电盒并将壁式固定在适当位置的条。

11.在壁灯孔上，取下电线的塑料夹克。使用电线剥离器，卸下每条电线绝缘的大约1英寸。用相应的电线从壁灯上扭动每根电线：黑色到黑色，白色至白色，铜或绿色到铜。使用电线连接器固定电线，将其塞入盒子中，然后根据制造商的说明安装壁灯。

12.在开关孔上，卸下电线的夹克。剥离大约1英寸的每根电线的末端，然后将开关接线：

• Twist the white wires together and cap them with a wire connector.
• 切成大约5英寸长的备用铜线（这称为辫子）。
• 将三条裸线扭转在一起，并用电线连接器盖住它们。
• 在短铜线（辫子）的自由端弯曲钩子，然后将其放在开关上的绿色螺钉上，然后拧紧螺丝。
• Attach the black wire coming from the outlet (the line) to the gold screw on the bottom of the switch. Attach the black wire heading to the sconce (the load) to the top gold screw.
• 拧紧所有螺钉，将电线塞入开关框中，然后将开关固定到位。安装开关盖板。

13.使用电线脱衣舞娘，从伸出插座盒中伸出的新电线上卸下1英寸的绝缘材料。如果只有一组电线运行到插座，请将开关的电线连接到出口上的两个空螺钉：

• 将黑线连接到金螺钉。
• Attach the white wire to the white screw.
• 切成大约5英寸长的备用铜线（这称为辫子）。
• 从插座上卸下铜线，然后拉直末端。
• Twist the three bare copper wires together and cap them with a wire connector.
• 在辫子的自由端弯曲钩子，将其放在开关上的绿色螺柱上，然后拧紧。

如果没有一组空的端子螺钉要接线，则此过程将起作用：

• 切三根辫子；一个黑色，一个白色，一个裸露。剥离末端。
• 从插座上卸下一组电线，然后将其末端弯曲。
• Working one color at a time, twist the end of the existing wire, the new wire from the switch, and the pigtail together. Repeat until all three colors are wired.
• 弯曲钩在辫子的自由末端，并将其连接到插座。将黑色的电线连接到金螺钉，白色电线上的白色螺钉将铜线和铜线连接到绿色螺钉。

14.将电线整齐地塞入电盒中，重新安装出口，然后将电源板塞入盖板。将断路器翻转回去，以恢复出口的电源。翻转开关以测试壁灯。

确保扫除一小块电线和干墙灰尘，然后退后一步，欣赏您的新sconce提供的额外照明。如果您愿意，请重复相同的过程，以在房屋周围添加更多的墙壁壁灯。bob体育app苹果下载

考虑坐着和阅读区域，卧室或其他需要增亮的地方。使用这种方法，您几乎可以在已经存在的任何地方安装壁灯。